English 
Chinese 
RTS Wall and Bead Sensors
$1.00 - $3.50
The room sensors are used to provide reliable, accurate temperature readings in surface-mount room environments, Energy Management Control Systems, compatible with all the leading control systems.They feature a standard plastic ventilated enclosure.
Product Highlights:
- Three low cost room temperature sensors to choose from.
- High precision thermistor or RTD, accurate to 0.2C(+/-.36F).
- The platinum RTD is accurate to 0.4C.
Available Options:
Room Temperature Sensor
RTS：
Dimensions:
RTS
RTS-Raw
RTS-Bead
| Weight | 0.01 kg |
|---|---|
| RTS type | RTS, RTS-Bead-120, RTS-Bead-4, RTS-RAW |
| Temperature Curve |
Related Products
-
Duct Temperature Sensor – Flange Mount
$4.30 - $6.30Availability: In stockOut of stock
This sensor is used to measure the supply and return temperature in HVAC system. The flange mount design makes it easy to install the sensor in tight quarters. There are several sensor elements to choose from which guarantee compatibility with all popular DDC systems. The probe in the photo is our standard model which is always in stock, it has a 8″ probe and a 120″ cable, and employs either a precision thermistor or platinum film sensor, so field calibration is not required. The 10ft(3m) cable is “Plenum Rated”.
-
Duct Averaging Temperature Sensors
$37.00 - $61.00Availability: In stockOut of stock
Temperature is detected by a range of thermistors. The
special mechanical construction the sensor is able to detect
temperature throughout its entire length. -
Thermowells
$4.50 - $7.50Availability: In stockOut of stock
These thermowells are designed for mounting temperature sensors in pipes and tanks.The thermowells are designed to handle this stress while providing good thermal contact with the fluid.They also provide isolation, if the sensor needs to be serviced the system can remain in operation without having to drain the lines. The thermowells are machined from a single piece of bar stock, there are no welds as found on competing products.
-
RTS3 Flush Mount Hidden Room Temp
$7.00 - $8.30Availability: In stockOut of stock
The room temperature sensor provide precision room temperature sensing in a discreet button form factor for all popular DDC systems.
-
Outdoor Air Temperature Sensor, Overmolded
$5.00 - $6.00Availability: In stockOut of stock
The temperature sensor is designed to measure outdoor air temperature in typical HVAC applications. Mounting is quick and easy using two screws and no electrical box. The thermistor is a well sealed stainless steel probe which is then inserted into a hard rubber PVC radiation shield. The cable is two meters long which allows terminating inside the building in an electrical enclosure or with flying leads. The cable can exit directly behind the probe and into the building through a hole, or it can exit vertically and run down the wall. A foam backing seals the hole in the wall if there is one and also serves to thermally insulate the probe from the wall. The probe is filled with thermal grease for quick response.
-
Temperature Transducer with Bacnet and Modbus RS485
$19.00 - $27.00Availability: In stockOut of stock
Duct mount temperature only transducer, Bacnet/Modbus over RS485, 0-10v 4-20ma output signal
-
Outdoor Air Temperature Sensor
$7.00 - $8.00Availability: In stockOut of stock
This sensor is used to measure the outside air temperature to allow the DDC system to coordinate the mechanical systems with actual building load conditions, enabling such strategies as free cooling, optimum start/stop, and supply temperature reset. The housing is made from PVC and stainless steel fittings which shield the probe from direct sunlight. There are three thermistor based models, and one RTD version to provide compatibility with the majority of DDC systems.
-
WTS6-I: Strap-On Insert Temperature Sensor
$5.00Availability: In stockOut of stock
The strap-on Insert sensor consists of a stainless steel sheath temperature sensor, thermal conducting compound, and an adjustable pipe bracket accessory. The stainless steel sheath temperature sensor is suitable for direct application to pipe surfaces for chilled or hot water measurement.
-
Probe Temperature Sensor
$2.20 - $3.80Availability: In stockOut of stock
This Probe Temperature Sensor comes standard with a 0.6″ Stainless Steel Temperature Sensor. This sensor is a 10K Thermistor, with an industry standard Type 2 curve.Connected to the end of the Sensor is 2 UL2468 26/2CAWG 105°C Black Wires with tinned ends.
