English 
Chinese 
Temperature Transducer with Bacnet and Modbus RS485
$19.00 - $27.00
Duct mount temperature only transducer, Bacnet/Modbus over RS485, 0-10v 4-20ma output signal
Product Highlights:
-High precision sensor accurate to 2% humidity over the entire temperature range.
-Duct mount style is suitable for typical HVAC and agricultural applications
-Field selectable span for the temperature range
-100% field changeable Temp/Hum module, no tools or calibration needed.
-Jumper select the output signal: 4~20mA or 0-10V
-BACnet MS/TP and Modbus RTU protocols over RS485.
-Enthalpy and dew point are available over the RS485 link
Available Options:
Duct temperature transmitter is applicable to all kinds of building automation, environment monitoring, HVAC systems. Product appearance is simple, direct connection terminals, convenient installation.Products use high performance embedded microprocessor, and high-precision sensors to meet all kinds of high precision,high stability of the temperature measurement requirements , and variety needs of different environments.Duct temperature sensor / transmitter has current,voltage, 485 output signal to select, using 485 serial port out put and Modbus communication protocol. It is commonly used in HVAC, electrical plant,environment monitoring,dynamic environment monitoring, agricultural environmental monitoring, meteorological environmental monitoring,environmental monitoring of biological pharmacy, airport,subway stations, hotel,museum,stadium, etc.
Dimension
Wiring Diagram
Part Num Scheme
Works with:Thermowell https://dev.bravocontrols.com/shop/brass-stainless-steel-thermowells/
| Weight | 0.1 kg |
|---|---|
| Module type | |
| Probe Length |
Related Products
-
Outdoor Air Temperature Sensor, Overmolded
$5.00 - $6.00Availability: In stockOut of stock
The temperature sensor is designed to measure outdoor air temperature in typical HVAC applications. Mounting is quick and easy using two screws and no electrical box. The thermistor is a well sealed stainless steel probe which is then inserted into a hard rubber PVC radiation shield. The cable is two meters long which allows terminating inside the building in an electrical enclosure or with flying leads. The cable can exit directly behind the probe and into the building through a hole, or it can exit vertically and run down the wall. A foam backing seals the hole in the wall if there is one and also serves to thermally insulate the probe from the wall. The probe is filled with thermal grease for quick response.
-
WTS6-E: Strap-On External Temperature Sensor
$5.00 - $6.00Availability: In stockOut of stock
The strap-on temperature sensor is used for sensing the temperature of pipework in heating, ventilation and air conditioning systems.
-
1K PT Temperature Sensors
$2.80 - $9.40Availability: In stockOut of stock
The 1K Platinum temperature sensors for building automation, agricultural and light industrial duty applications.
-
Thermowells
$4.50 - $7.50Availability: In stockOut of stock
These thermowells are designed for mounting temperature sensors in pipes and tanks.The thermowells are designed to handle this stress while providing good thermal contact with the fluid.They also provide isolation, if the sensor needs to be serviced the system can remain in operation without having to drain the lines. The thermowells are machined from a single piece of bar stock, there are no welds as found on competing products.
-
Outdoor Air Temperature Sensor
$7.00 - $8.00Availability: In stockOut of stock
This sensor is used to measure the outside air temperature to allow the DDC system to coordinate the mechanical systems with actual building load conditions, enabling such strategies as free cooling, optimum start/stop, and supply temperature reset. The housing is made from PVC and stainless steel fittings which shield the probe from direct sunlight. There are three thermistor based models, and one RTD version to provide compatibility with the majority of DDC systems.
-
High temperature over molded floor heating sensor
$5.00Availability: In stockOut of stock
High temperature over molded floor heating sensor,4.5m cable length,6.0mm diameter pipe,10k Type2 thermistor.
-
WTS5: Strap-on Water Temperature Sensor
$7.00 - $8.00Availability: In stockOut of stock
This sensor is used to measure water temperature of heated or chilled water and other liquids found in the various mechanical systems of building. The sensor is especially intended for strapping to the outside of a pipe when there is no opportunity to install a well such as in a retrofit or additions to an existing system.The strap on probe is useful in applications such as monitoring batteries, transformers, generators, and generally any place where a complete assembly can not be mounted,Ice rink slabs and soil temperature are other applications.
-
WTS6-I: Strap-On Insert Temperature Sensor
$5.00Availability: In stockOut of stock
The strap-on Insert sensor consists of a stainless steel sheath temperature sensor, thermal conducting compound, and an adjustable pipe bracket accessory. The stainless steel sheath temperature sensor is suitable for direct application to pipe surfaces for chilled or hot water measurement.
-
Tamper Proof room temperature sensor
$5.00 - $6.00Availability: In stockOut of stock
The tamper proof room temperature sensor with Torx security screws designed for use with building automation systems in commercial buildings, hospitals, museums or other facilities requiring accurate measurement of room temperature. This sensor can be directly mounted to drywall or an 11-10 electrical handy box.
